WELCOME TO OUR STORE

SUPPLEMENTAL HEATING APPLIANCES

SHOP FOOT WARMERS

EASY TO INSTALL DIY UNDERFLOOR HEATING KITS 

SHOP FLOOR HEATING KITS

SHOP HEATING APPLIANCES

Supplemental Heating Appliances Designed to Warm Cold Spots in Your Home Quickly and Economically. 

Low Energy Consumption.  No Installation.  Simply Plug In and Enjoy!

SHOP FLOOR HEATING KITS

We’ve made DIY Floor Heating Easy With Our Range Of  Under Floor Heating Kits.  Suitable for Installation under Tile, Laminate, Carpet and Vinyl Flooring.

Kits Include Everything Needed to Install Under Floor Heating Yourself!

YouTube

COLDBUSTER DIY Floor Heating Kits make it easy to install floor heating yourself. Timestamps 00:00 Intro 00:10 What's In The DIY Floor Heating Kits? 00:39 How To Test The Heater Before the Floor Heating Installation Box contents include everything needed, a step-by-step instruction manual, and a support line should you need assistance. Pre-testing the heater is important before the floor heating installation. Instructions are included with a damage detection monitor. The KlimaGuard® monitor ensures early damage detection during the floor heating installation process. 2:20
DIY Floor Heating Made Easy - What's In The DIY Floor Heating Kits?
YouTube Video UExWWWRiZ2x0bW5lY0x6R3NTOTRZYktwc29Ubk1GN2RQYi41NkI0NEY2RDEwNTU3Q0M2
Planning and preparation of the floor and area to be heated before the floor heating installation. Timestamps 00:00 Intro 00:10 Mark The Position Of The Thermostat 00:20 How To Prepare A Cavity For the Connector Blocks 00:39 Preparing The Floor Area Before The Floor Heating Installation Ensure the floor surface is smooth and dry; unpainted and free of dust, oil, grease, tar, or glue residue. Carefully plan the position and layout of the heater in the area to be heated. The heating strip is manufactured in a strip form either 300 or 600mm wide. The position of the thermostat/electrical supply point must be marked. Below the controller position or supply point, prepare the floor by chipping away the floor screed with a small chisel to form a cavity about 10mm deep to allow the connector blocks to be recessed into the floor. 0:48
How To Install Floor Heating - Planning and Preparation
YouTube Video UExWWWRiZ2x0bW5lY0x6R3NTOTRZYktwc29Ubk1GN2RQYi4yODlGNEE0NkRGMEEzMEQy
This video is a demo of the correct method of placing the floor heating mats Timestamps 00:00 Intro 00:10 Apply The Primer To The Area Where The Heater Will Be Fitted 00:35 How To Lay Down The Floor Heating Mat 01:44 How To Ensure Enough Element Wire is Available Back To The Power Source 02:15 How To Tape The Heating Mat Down With The Double-Sided Tape on The Heater 03:36 How To Place The Connector Blocks In The Cavity 04:32 Correct Method To Tape The Returning Element Wires Down 05:47 How To Install The Thermostat Floor Sensor Probe For The Heating System Apply the KlimaCoat™ primer to the area where the heater(s) will be fitted, using a paint roller, and allow to dry. Unroll the heater on the floor. Cut the tapes where necessary to allow the element to be located in the best position. Take care not to damage the element. Try not to walk or stand on the heating element. Pull the wax paper backing off the double-sided tape a little at a time and, keeping it straight, stick it to the floor. Do the same with the tape on the other side of the heater, ensuring that the element is straight and under slight tension. Element wires should never cross or be closer than 50mm apart. Place the blocks in the cavity and tape them down. If other heaters are to be connected to the same power supply, install them in the same manner. Keep the elements at least 50mm apart. 6:16
How To Install Floor Heating - Part 1
YouTube Video UExWWWRiZ2x0bW5lY0x6R3NTOTRZYktwc29Ubk1GN2RQYi4wMTcyMDhGQUE4NTIzM0Y5
In this video, we take a look at the final steps of the floor heating installation - installing the mesh and screeding the floor. Timestamps 00:00 Intro 00:10 How To Install The Self-Adhesive Mesh Over The Floor Heating 01:16 How To Arrange the Leading Wires Neatly Together Leading To The Thermostat 01:39 Re-connecting The Damage Detection Monitor 02:21 Applying The Tile Adhesive And Bonding Liquid 02:31 Correct Way To Screed Over The Mesh Lay the green mesh, sticky side down, over the heater. Cut the mesh as necessary to cover all the heater elements including those to the connector blocks. Press the mesh down so that it sticks to the floor and keeps the element in position. Do not overlap the mesh. For every 5m² of heater to be covered, mix 20kg of good quality, fast-set floor tile adhesive with the correct amount of liquid - see the tile adhesive guide. Spread the tile adhesive evenly over the mesh with a steel or nylon float with rounded corners. Make sure that the element stays in position and that the adhesive is pushed through the mesh. Use additional adhesive if the element is not completely covered. The amount of KlimaFlex™ and mesh is sufficient for the heater size it comes with. The KlimaGuard® monitor must remain connected until tiling and grouting is complete. This is to ensure that you are alerted should any damage to the element occur during the tiling and grouting process. If the heater is damaged and this is only noticed after the tiling is complete, repairs are more difficult and costly but can be done. 3:09
How To Install Floor Heating - Part 2
YouTube Video UExWWWRiZ2x0bW5lY0x6R3NTOTRZYktwc29Ubk1GN2RQYi41MjE1MkI0OTQ2QzJGNzNG
Subscribe
Call Us Now!